< Go back to the Trac‑Rite commercial garage doors

Trac‑Rite 955WL

The Trac‑Rite Model 955 Roll Up Door is designed for service in wide range of Light‑Duty Commercial applications - including farm buildings, warehouses, car wash facilities, auto body shops… The Trac‑Rite 955WL Door is based on the 955 Model and is ideal for the same range of uses - but the 955WL features WindLocks to provide Maximum Wind Load Capability.

Tough & Stylish With Maximum Wind Load Resistance

The Trac-Rite 955WL's continuous curtain of solid steel is available in a variety of colors and in custom sizes from (8'-12'W) x (3'-12'8"H) in 1" increments. Maximum heights vary depending on width.

The Trac-Rite WindLock System

When wind blows against the 955WL steel curtain, the door's WindLocks engage with the door guide to produce a strong interlocking grip that maintains the curtain securely in it's guide to provide Maximum Wind Load Resistance.

Trac‑Rite 955WL door applications

Trac-Rite 955 with WindLock System

Light-Duty Commercial:

Auto Body Shops
Boat Houses
Car Washes
Cold Storage
Dock Doors
Machine Shops

Roll-Up Interior Partition Dividers
Post Frame Buildings
Sheds
Warehousing Applications
High Eave Structures with Relatively Low Door Heights

Trac‑Rite 955WL door specifications

Design type

Live axle: door axle rotates in bracket bearing during operation.

Drums

Stamped, continuously welded at the hub. 9‑5⁄8" diameter spiral x 1‑1⁄4" wide. 16‑gauge, zinc‑coated steel. Four drums on all doors over 8' wide.

EP3 Springs

Two helical torsion, oil tempered springs, coated to halt corrosion and increase life.

Axle

1‑5⁄16" outside diameter, schedule 80, steel tubing.

Tensioning System

Springs come with a zinc-coated cast steel tension wheel and winding bar for ease of adjusting spring tension.

Curtain

Roll-formed sections, factory-seamed from 26-gauge, Grade 80 galvanized steel. Siliconized polyester finish in 13 standard colors. Full-length 2" felt tape located at each drum.

Curtain Windlocks

10‑gauge, zinc‑coated steel, secured to door with two 3⁄16" rivets.

Bottom Assembly

Zinc‑coated steel bottom angle mounted to corrosion‑resistant aluminum extrusion with stainless steel bolts. TPE blade astragal also included.

Brackets

10‑gauge, cold‑formed, zinc‑coated steel. Grease‑packed ball bearings are factory installed in the bracket.

Guides

16‑gauge, zinc‑coated, 2‑¾" deep. Featuring polypropylene guide runners to assure smooth operation and prevent steel‑on‑steel contact. Guide WindLock bar manufactured from 12‑gauge, zinc‑coated steel.

Interior Lock

12‑gauge, zinc‑coated steel slide bolt engages a lock strike attached to the side guide. Two locks per door fasten to the bottom assembly and are suitable for padlocking.

Mounting Fasteners

Steel or wood fasteners included. For masonry openings, mounting clips and anchoring system are sold separately:

Steel:
Bracket: ¼" x 1" self‑drilling screws
Jamb: ¼" x 1" self‑drilling screws

Wood:
Bracket: 3⁄8" x 2‑½" lag bolt
Jamb: ¼" x 1‑½" self‑drilling screws

Masonry: For masonry openings, mounting clips are sold separately. Masonry anchors must be furnished by the Buyer.

Door Stop

12‑gauge, zinc‑coated L‑shaped stops mount to guides for increased strength.

Exterior Handle

Powder coated, zinc‑plated outside handle.

Pull Rope Handle

Molded plastic rope handle with long-lasting rope.

Design type	Live axle: door axle rotates in bracket bearing during operation.
Drums	Stamped, continuously welded at the hub. 9‑5⁄8" diameter spiral x 1‑1⁄4" wide. 16‑gauge, zinc‑coated steel. Four drums on all doors over 8' wide.
EP3 Springs	Two helical torsion, oil tempered springs, coated to halt corrosion and increase life.
Tensioning System	Springs come with a zinc-coated cast steel tension wheel and winding bar for ease of adjusting spring tension.
Axle	1‑5⁄16" outside diameter, schedule 80, steel tubing.
Curtain	Roll-formed sections, factory-seamed from 26-gauge, Grade 80 galvanized steel. Siliconized polyester finish in 13 standard colors. Full-length 2" felt tape located at each drum.
Curtain Windlocks	10‑gauge, zinc‑coated steel, secured to door with two 3⁄16" rivets.
Bottom Assembly	Zinc‑coated steel bottom angle mounted to corrosion‑resistant aluminum extrusion with stainless steel bolts. TPE blade astragal also included.
Brackets	10‑gauge, cold‑formed, zinc‑coated steel. Grease‑packed ball bearings are factory installed in the bracket.
Guides	16‑gauge, zinc‑coated, 2‑¾" deep. Featuring polypropylene guide runners to assure smooth operation and prevent steel‑on‑steel contact. Guide WindLock bar manufactured from 12‑gauge, zinc‑coated steel.
Interior Lock	12‑gauge, zinc‑coated steel slide bolt engages a lock strike attached to the side guide. Two locks per door fasten to the bottom assembly and are suitable for padlocking.
Mounting Fasteners	Steel or wood fasteners included. For masonry openings, mounting clips and anchoring system are sold separately: Steel: Bracket: ¼" x 1" self‑drilling screws Jamb: ¼" x 1" self‑drilling screws Wood: Bracket: 3⁄8" x 2‑½" lag bolt Jamb: ¼" x 1‑½" self‑drilling screws Masonry: For masonry openings, mounting clips are sold separately. Masonry anchors must be furnished by the Buyer.
Door Stop	12‑gauge, zinc‑coated L‑shaped stops mount to guides for increased strength.
Exterior Handle	Powder coated, zinc‑plated outside handle.
Pull Rope Handle	Molded plastic rope handle with long-lasting rope.

Note: Product specifications are subject to change without notice.

Trac‑Rite 955WL door wind load ratings

All Trac-Rite door models, both standard and WindLock, are put through rigorous wind testing - witnessed and certified by an independent test lab. Trac-Rite doors are approved for installation in buildings affected by Florida Building Commission regulations concerning wind testing and manufacturing certifications.

955WL Door width